SFS Suomen Standardit

 

This document specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programmes and groups for bayonet coupling circular connectors, intended for use in an operating temperature range of -65 °C to 175 °C or 200 °C continuous according to the class and models.

 

This document specifies a method for the determination of the softening point of bitumen and bituminous binders in the range of 28 °C to 150 °C. The method described also applies to bituminous binders that have been recovered from bituminous mixes, e.g. by extraction according to EN 12697 3 [1]. The change from mercury thermometers to electronic temperature devices has revealed that the temperature definition in the mercury thermometer has not been precise enough to make a correct, unbiased transfer to electronic devices. Care should be taken for softening points ring and ball above 100 °C as the condition may have changed from previous practice to present days testing equipment. Below approximately 100 °C the difference in temperature readings between electronic and mercury stem thermometer is acceptable compared to the repeatability of this test method.

 

This document specifies the general characteristics, conditions for qualification, acceptance and quality assurance, as well as the test methods and groups for fibre optic cables with a cladding of 125 µm outside diameter.

 

This document specifies the required characteristics of a semi-rigid light weight coaxial cable, 50 O, type KX for use in aircraft electrical systems at operating temperature between -55 °C and 200 °C and specially for high frequency up to 6 GHz. Nevertheless, if needed, -65 °C is also acceptable as shown by rapid change of temperature test.

 

This document specifies the characteristics of hermetic jam-nut mounted receptacles in the family of bayonet coupling circular connectors, intended for use in an operating temperature range of - 65 °C to 175 °C or 200 °C continuous. It applies to models specified in Table 4. For plugs and protective covers, see EN 3646 008 and EN 3646 009 respectively.

 

The purpose of this document is to: - identify and describe, in a structured way, the principles of the integrated logistic support (ILS) activities and tasks for the main types of stakeholders in the system life cycle, from the expression of need to disposal; - place the activities, tasks and ILS deliverables within the programme execution; - identify the main selection and sizing of activities and tasks criteria according to the nature and the requirements of the programme; - control the relations with the other aspects of programme management. This document covers the following subjects: - management of ILS (definition, implementation and running of the processes); - expression of the support requirements; - elaboration of the contracts (e.g. for development, maintenance, supply - implementation of the tasks and processes. This document is also related to the following subjects: - relations with costs and lead times control, configuration management, performance and RAMS management, quality assurance, documentation management; - regulations (e.g. information system security, export controls, safety at work); - human and organisational factors (HOF); - environment (e.g. RoHS, REACh); - information systems (IS) and the links between them; - logistics information systems (LIS); - in-service support (ISS) activities; - configuration management of ILS objects; - life cycle. The following stakeholders are concerned by ILS: - users in the broadest sense: operators, maintenance operators, administrators, dismantlers of the system, trainers; - the customer, who: - prepares technical and contractual specifications of need with which the system shall comply, - sets up the funding of the programme, - oversees the realization and commissioning of the main system and of the support system, - facilitates the feedback; NOTE 1 At the highest level of the system, the customer can also be referred to as the "project owner". NOTE 2 The "main system" can also be referred to as the "system of interest". - the supplier(s) who deliver a system (main and support) to the customer, which meets the performance specifications, including the regulatory requirements, on time and for the agreed cost, throughout the system life cycle; NOTE At the highest level of the system, the supplier can also be referred to as the "industrial prime contractor". - the regulatory authorities that supervise and approve the support processes and equipment, as needed. The principles laid down in this document can be applied, after adaptation, to all the customer/supplier relations resulting from the breakdown of the main contract into sub-contracts.

 

 

This document specifies the ISO base media file format, which is a general format forming the basis for a number of other more specific file formats. This format contains the timing, structure, and media information for timed sequences of media data, such as audio-visual presentations.

 

This part of ISO 6182 specifies performance, requirements, methods of test and marking requirements for the following equipment for use in automatic fire protection systems Performance and test requirements for trim valves for alarm valves are not covered by this part of ISO 6182. The requirements for pressure reducing valves and fire pump relief valves are provided by ISO 6182 Part 16 and Part 17.

 

This document specifies a test method for the quantitative determination of the antifungal activity by measuring the intensity of luminescence produced by an enzymatic reaction [adenosine triphosphate (ATP) method]. This document is applicable to various kinds of textile products, such as fibres, yarns, fabrics, clothing, bedclothes, home furnishings and other miscellaneous goods. Based on the intended application and on the environment in which the textile product is to be used, the user can select the most suitable evaluation method from the following methods before enumeration by the ATP method:

 

Within the context of the ISO/IEEE 11073 family of standards for device communication, a normative definition of communication is established in ISO/IEEE 11073-10421:2012 between personal telehealth peak expiratory flow monitor devices and compute engines (e.g. cell phones, personal computers, personal health appliances, and set top boxes) in a manner that enables plug-and-play interoperability. Appropriate portions of existing standards are leveraged, including ISO/IEEE 11073 terminology, information models, application profile standards, and transport standards. The use of specific term codes, formats, and behaviors is specified in telehealth environments restricting optionality in base frameworks in favor of interoperability. A common core of communication functionality is defined for personal telehealth peak expiratory flow monitor devices.

 

ISO 18363 specifies a procedure for the simultaneous determination of 2-MCPD esters (bound 2-MCPD), 3-MCPD esters (bound 3-MCPD) and glycidyl esters (bound glycidol) in a single assay, based on acid catalysed ester cleavage and derivatization of cleaved (free) analytes with phenylboronic acid (PBA) prior to GC/MS analysis. ISO 18363-3 is applicable to solid and liquid fats and oils. For all three analytes the limit of quantification (LOQ) is 0,1 mg/kg and the limit of detection (LOD) is 0,03 mg/kg.

 

This document describes the transaction information requirements of the transactions used in the basic collaborations described in EN 17015-1 Electronic Public Procurement – Catalogue – Choreographies. For each transaction there is an overview, the transaction business requirements and the transaction information requirements model containing definitions of terms, usage descriptions and cardinality of the information elements. The document describes the following transactions: 1) Catalogue; 2) Catalogue Response 3) Pre-award Catalogue Request 4) Pre-award Catalogue 5) Shopping Cart How to claim compliance to a transaction is described in paragraph 6. How to claim conformance to a transaction is described in paragraph 6.

 

This document specifies a method for the determination of cyclosiloxanes in chemicals used in the tanning industry

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat-resisting (cobalt, nickel and iron-based alloys) alloy plates, sheets and strips. It is presupposed to be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat-resisting alloy bars and sections. It is presupposed to be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat resisting alloy tube. It is presupposed to be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat resisting alloy wire. It is presupposed to be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat-resisting alloy forging stock. It is presupposed to be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule.

 

This document specifies the requirements for the ordering, manufacture, testing, inspection and delivery of pre-production and production forgings in steel and heat-resisting alloys.