Kemesta

 

This standard specifies methods for the simultaneous measurement of the fibre tensile strength distribution and the fibre resin interfacial shear strength of recycled carbon fibres using the modified fragmentation test[1]. The Young's modulus and fibre diameter of the fibre to which this standard applies must already be known. The thermal shrinkage of the polymer must also be known.

 

This document specifies a method for determining the scratch properties of plastics under defined conditions. The method involves making a scratch by moving a hard tool (scratch tip) under specified conditions of load and speed across the surface of a test specimen and then assessing the result. The method is used to investigate the behaviour of specified types of specimens under the scratch conditions defined and for classifying the type of scratch of specimens within the limitations inherent in the test conditions. It can also be used to determine comparative data for different types of material by means of a so-called scratch map in which the types of scratch behaviour for each set of test conditions of test load and test speed are determined using the basic method of constant-load testing, and also by means of the so-called critical normal load (see 3.8) determined using an alternative method of linearly increasing load testing. “The method is suitable for use with the following range of materials. The method specifies the preferred dimensions for the test specimen and the preferred scratch-tip geometry.

 

This document specifies the apparatus and the analytical method for determining the content of in-can isothiazolinone preservatives in water-dilutable coating materials or related products.

 

The method describes the quantitative determination of the in-can total formaldehyde content in water-dilutable coating materials. Main sources of formaldehyde are preservatives.

 

The method describes the quantitative determination of the concentration of in-can free formaldehyde in water-dilutable coating materials. The determination method A for in-can free formaldehyde can be only of limited suitability for pigmented systems, as the inherent coloration of the material may have an influence on the detection.

 

This document specifies the apparatus and analytical method for determining the content of in-can isothiazolinone preservatives in water-dilutable coating materials or related products. Note The document is also applicable for polymer dispersions.

 

The method describes the quantitative determination of the in-can total formaldehyde content in water-dilutable coating materials. Main sources of formaldehyde are preservatives. NOTE: The standard is also applicable for polymer dispersions.

 

The method describes the quantitative determination of the concentration of in-can free formaldehyde in water-dilutable coating materials. Note: The standard can also be applied for polymer dispersions. The determination method for in-can free formaldehyde can be only of limited suitability for pigmented systems, as the inherent coloration of the material may have an influence on the detection method.

 

This document specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes. This document contains: Annexes A and B specify further variations in the testing protocol according to specific conditions. A guide to the use of these methods is given in Table 1.

 

This part of ISO 16365 establishes a system of designation for thermoplastic polyurethane elastomers, which is based on ISO 1043 (all parts) and ISO 11469. The designation system may be used as the basis for specifications. The designation system is applicable to all thermoplastic polyurethane elastomers. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colourants, fillers or other additives, etc. The types of thermoplastic polyurethane are differentiated from each other by a classification system based on appropriate levels of the designatory properties: and on information about the alternating hard and soft segments in the main chain, the intended application and/or method of processing, important properties, additives, colour, fillers, and reinforcing materials. It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 16365 does not provide engineering data, performance data, or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, it is intended that they be determined in accordance with the test methods specified in ISO 16365-2, if suitable. In order to specify a thermoplastic elastomer for a particular application or reproducible processing, additional requirements are intented to be given in data block 5 (see 3.1 and 3.6).

 

This document specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes. This document contains: — Method 1: Self adhesive tapes ? Measurement of peel adhesion from stainless steel at an angle of 180°; — Method 2: Self adhesive tapes ? Measurement of peel adhesion from its own backing at an angle of 180°; — Method 3: Self adhesive tapes ? Measurement of peel adhesion of double sided and transfer tapes at an angle 180°; — Method 4: Self adhesive tapes ? Measurement of adhesion of the liner to an adhesive tape at an angle of 180°. Annexes A and B specify further variations in the testing protocol according to specific conditions.

 

This document specifies two methods of the determination of free formaldehyde (HCHO) in polymer dispersions. This document is applicable to acrylic, acrylonitrile butadiene, carboxylated styrene-butadiene and vinyl acetate polymer dispersions. This document can also be applicable to polymer dispersions of other compositions. Method A (UV/Vis spectrometer method) is applicable to polymer dispersions with a free-formaldehyde content higher than 10 mg/kg. Method B (HPLC method) is applicable when lower formaldehyde contents have to be determined or arbitration analyses have to be carried out.

 

This document specifies a test method for comparing the compression shear strength of adhesive bonds and solid wood at 180 °C and a second elevated temperature. The maximum load of the test pieces after exposure to 180 °C and a specific elevated temperature for a specified duration of time is evaluated. It is applicable to adhesives used in load bearing timber structures and to other wood adhesives. This method is intended primarily to obtain data for the performance of wood adhesives at high temperatures. The result of this method (temperature class) can be used to classify the adhesive with respect to its performance in fire.

 

This part of ISO 5267 specifies a method for determination of the drainability of water from a pulp suspension in terms of the “Canadian Standard” freeness in millilitres. In principle, this method is applicable to all kinds of pulp in aqueous suspension.

 

This document specifies methods for measuring tyre-to-road abrasion rate on open road circuits, in an actual driving environment. This document is applicable to passenger cars pneumatic tyres subject to ISO 4000-1 with the following exclusions:

 

This document describes the quality grades for sorted Polypropylene (PP) waste streams as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. Polypropylene waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The scheme provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party. This document does not cover the general characterization addressed in EN 15347-1.

 

This document describes the quality grades for sorted poly(ethylene terephtalate) (PET) waste streams as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PET waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The scheme provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party. This document does not cover the general characterization addressed in EN 15347-1.

 

This document describes the quality grades for sorted poly(vinyl chloride) (PVC) waste streams as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PVC waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The scheme provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party. This document does not cover the general characterization addressed in EN 15347-1.

 

This document describes the quality grades for sorted polystyrene (PS) waste streams as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. PS waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The scheme provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party. This document does not cover the general characterization addressed in EN 15347-1.

 

This document describes the quality grades for sorted Polyethylene (PE) waste streams as well as specific test methods laying out those properties for which the supplying party of the waste makes information available to the receiving party. Polyethylene waste quality grades are based on pre-determined sets of characteristics, taking into account sectorial and market specificities and related information needs and tests methods. The scheme provides for a division of information between "Required Data", where a statement is required, and additional "Optional Data" as agreed between the supplying and receiving party. This document does not cover the general characterization addressed in EN 15347-1.