Kemesta

 

This document specifies a general method of test for comparing the colour of a coloured pigment with that of an agreed sample. Either of the procedures described in Clause 6 and Clause 7 is acceptable but the method using an automatic muller is the reference method.

 

This document specifies a general method of test for determining the pH value of an aqueous suspension of a sample of pigment or extender.

 

This document specifies general test methods for determining the resistance to water, acid, alkali-and solvent of pigments.

 

This document specifies requirements for the construction, performances, minimum labelling and mandatory instructions for use of other pyrotechnic articles of the following generic types: - flares; - flash devices; - gas generators; - heaters; - other cartridges; - pyromechanical devices; - pyrotechnic actuated dispersers; - rockets and rocket motors; - semi-finished pyrotechnic articles; - smoke/aerosol generators; - sound emitters. This document does not apply to pyrotechnic articles for vehicles, ignition devices and cartridges for powder actuated tools (PAT). The following standards apply to the excluded articles: - EN ISO 14451 1, Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 1: Terminology (Under preparation) - EN ISO 14451 2, Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 2: Test methods (Under preparation) - EN ISO 14451 3, Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 3: Labelling (Under preparation) - EN ISO 14451 4, Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 4: Requirements and categorization for micro gas generators (Under preparation) - EN ISO 14451 5, Pyrotechnic articles for vehicles – Part 5: Requirements and categorization for airbag gas generators (Under preparation) - EN ISO 14451 6, Pyrotechnic articles – Pyrotechnic articles for vehicles – Part 6: Requirements and categorization for airbag modules (Under preparation) - EN ISO 14451 7, Pyrotechnic articles – Pyrotechnic articles for vehicles – Part 7: Requirements and categorization for seatbelt pretensioners (Under preparation) - EN ISO 14451 8, Pyrotechnic articles – Pyrotechnic articles for vehicles – Part 8: Requirements and categorization for igniters (Under preparation) - EN ISO 14451 9, Pyrotechnic articles – Pyrotechnic articles for vehicles – Part 9: Requirements and categorization for actuators (Under preparation) - EN ISO 14451 10, Pyrotechnic articles – Pyrotechnic articles for vehicles – Part 10: Requirements and categorization for semi-finished products (preparation) - EN 16264, Pyrotechnic articles – Other pyrotechnic articles – Cartridges for powder actuated tools (Under preparation) - EN 16265, Pyrotechnic articles – Other pyrotechnic articles – Ignition devices (Under preparation)

 

This document specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of fully wrapped composite gas cylinders for compressed, liquefied and dissolved gases. NOTE 1 For the purposes of this document, the word “cylinder” includes tubes (seamless transportable pressure receptacles of a water capacity exceeding 150 l and of not more than 3 000 l). This document is applicable to cylinders that comprise a liner of metallic material (welded or seamless) or non-metallic material (or a mixture thereof), reinforced by a wound composite consisting of fibres of glass, carbon or aramid (or a mixture thereof) embedded in a matrix. This document is also applicable to composite cylinders without liners. This document is not applicable to gas cylinders which are partially covered with fibres and commonly called “hoop wrapped” cylinders. For hoop wrapped composite cylinders, see EN 12257. NOTE 2 This document does not address the design, fitting and performance of removable protective sleeves. Where these are fitted, they are considered separately. This document is primarily for compressed, liquefied and dissolved gases other than LPG. NOTE 3 For dedicated LPG cylinders, see EN 14427.

 

The method specified can also be applied to the examination of other powders or granules which are insoluble in water. It is neither applicable to hydrophobic nor pelletized materials. In the test apparatus the material under test, dispersed in water, is brought into centrifugal motion by a system of rotating jets of water. he water flushes the fine particles through the sieve, the coarse particles being retained on the sieve. The residue on the sieve is dried and weighed. - Cancels and replaces ISO 787/18-1973 and constitutes its technical revision.

 

This document specifies test methods and minimum performance requirements for coating systems for wind-turbine rotor blades, both prior and following weathering and climatic testing. It provides a comprehensive summary of appropriate weathering and climatic testing procedures.

 

This document specifies minimum requirements and weathering for coating systems for wind-turbine rotor blades.

 

This document specifies a method to measure the total unsaturation of polyether polyols for use in the production of polyurethanes by a Raman spectrometric method. It is not applicable to unsaturated compounds that are conjugated with a carbonyl group, a carboxyl group, or a nitrile group.

 

This document specifies the requirements for periodic inspection and testing to verify the integrity of cylinders and tubes to be re-introduced into service for a further period of time. This document is applicable to seamless steel and seamless aluminium-alloy transportable gas cylinders (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l and to seamless steel and seamless aluminium-alloy transportable gas tubes (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity greater than 150 l. It also applies, as far as practical, to cylinders of less than 0,5 l water capacity. This document does not apply to the periodic inspection and maintenance of acetylene cylinders or to the periodic inspection and testing of composite cylinders. NOTE Unless noted by exception, the use of the word "cylinder" in this document refers to both cylinders and tubes.

 

This document specifies the requirements for periodic inspection and testing to verify the integrity of cylinders and tubes to be re-introduced into service for a further period of time. This document is applicable to seamless steel and seamless aluminium-alloy transportable gas cylinders intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l and to seamless steel and seamless aluminium-alloy transportable gas tubes intended for compressed and liquefied gases under pressure, of water capacity greater than 150 l. It also applies, as far as practical, to cylinders of less than 0,5 l water capacity. This document does not apply to the periodic inspection and maintenance of acetylene cylinders or to the periodic inspection and testing of composite cylinders. NOTE Unless noted by exception, the use of the word “cylinder” in this document refers to both cylinders and tubes.

 

This document specifies an oven-drying method for the determination of the moisture content of a lot of paper and board. The procedure in Clause 8, describing how the test pieces are drawn from the lot, is performed at the time of sampling. This document is applicable to every type of lot of paper and board, including corrugated board and solid board, provided that the paper or board does not contain any substances, other than water, that are volatile at the temperature specified in this document. NOTE For determination of the dry matter content of a sample of paper or board, e.g. for calculation of the dry mass of the sample, ISO 638[1] can be used.

 

ISO 287:2017 specifies an oven-drying method for the determination of the moisture content of a lot of paper and board. The procedure in Clause 8, describing how the test pieces are drawn from the lot, is performed at the time of sampling. ISO 287:2017 is applicable to every type of lot of paper and board, including corrugated board and solid board, provided that the paper or board does not contain any substances, other than water, that are volatile at the temperature specified in this document. NOTE For determination of the dry matter content of a sample of paper or board, e.g. for calculation of the dry mass of the sample, ISO 638[1] can be used.

 

This document establishes a classification of wood adhesives for non-structural applications for exterior use without protection by an adequate surface coating. This document specifies performance requirements and durability classes of such adhesives for use in an environment corresponding to the defined conditions. The performance requirements of this document apply to the adhesive only, not to wooden products. This document is primarily intended to assess the performance of adhesives. The requirements apply to the type testing of the adhesives. Production control activities are outside the scope of this document. NOTE For the assessment of end product bonding quality, see Annex A.