Toimialayhteisöt

 

This document defines terms for microlens arrays. It applies to arrays of very small lenses formed inside or on one or more surfaces of a common substrate. This document also applies to systems of microlens arrays.

 

This part of this European Standard defines performance requirements which are specified as lighting classes for road lighting aiming at the visual needs of road users, and it considers environmental aspects of road lighting. NOTE Installed luminous intensity classes for the restriction of disability glare and control of obtrusive light and installed glare index classes for the restriction of discomfort glare are defined in the informative Annex A. Lighting of pedestrian crossings is discussed in the informative Annex B. Disability glare evaluation for conflict areas (C classes) and pedestrian and pedal cyclists (P classes) is discussed in the informative Annex C.

 

This European Standard specifies the conventions and mathematical procedures to be adopted in calculating the photometric performance of road lighting installations designed in accordance with the parameters described in EN 13201-2 to ensure that every lighting calculation is based on the same mathematical principles. The design procedure of a lighting installation also requires the knowledge of the parameters involved in the described model, their tolerances and variability. These aspects are not considered in this part of EN 13201 but a procedure to analyse their contribution in the expected results is suggested in EN 13201-4 and it can also be used in the design phase.

 

This document deals with the design considerations and essential principles for internal plastering systems and application of plastering systems. The different parts of the EN 13914 series of standards specify requirements and recommendations for detailing, design and material considerations, the selection of mixes and the application of gypsum plasters, gypsum/lime plasters, lightweight plasters, lime/gypsum-, cement- and cement/lime-based plasters, lime-based plasters, clay plasters, silicate plasters, organic plasters, polymer-modified plasters, etc. This document does not deal with the following: - external finishes; - painting and/or preparation; - impregnations; - structural repair of concrete; - prefabricated fibre-reinforced plaster elements; - surface treatments. Because of the many varied materials, practices and different climatic conditions, it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable by all practitioners. NOTE Local or national regulations take precedence when applicable.

 

This document specifies requirements and recommendations for the design, preparation and application of - renders based on cement, lime or other mineral binders, and/or combinations thereof, masonry cement and polymer modified binder based external renderings, in accordance with EN 998-1 or site made renders; - renders based on organic binders in accordance with EN 15824 on all common types of backgrounds. It includes rendering on both new and old backgrounds and the maintenance and repair of existing work. This document gives guidance on the use of established site, factory and semi-finished factory-made renders. This document does not cover the following: a) the use and application of special renders for liquid retaining structures, e.g. coatings, and for backgrounds to cladding systems; b) the structural repair of concrete; c) the installation of external thermal insulation composite systems (ETICS); d) the specification and use of sealants used to seal joints for use with rendering; e) the use of gypsum-based renders; f) renders on historical monuments or buildings in protected areas; g) the design and installation of flashings at windowsills and elsewhere. Because of the many varied materials, practices and different climatic conditions, it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable by all practitioners. NOTE Local or national regulations take precedence when applicable.

 

This document is applicable to endodontic ultrasonic inserts, operated in combination with either air or electrically powered stand-alone handpieces or handpieces connecting to dental units. This document specifies requirements and test methods for inserts, and requirements for marking, labeling and packaging.

 

The proposed standard will specify the terms and definitions, technological process, technical requirements, environmental protection requirements, and safety requirements, for short loop recycling of recyclable bulk neodymium iron boron (Nd-Fe-B) sintered permanent magnets. This document is applicable to recyclable bulk Nd-Fe-B sintered magnet resources from end of life (EOL) products and manufacturing process.

 

This document provides a taxonomy for the levels of automation of flight control subsystems for uncrewed aircraft systems (UAS) based on the considerations for automated flight control capability, and provides the human-machine roles under different flight functions. This document is intended to support the implementation and evaluation of the flight control subsystems, but does not describe the methods for designing the functions of these systems, nor does it constrain the number or types of functions which a flight control subsystem may contain.

 

This document specifies and classifies the component/product performance characteristics, which may be necessary for the design, rating and dimensioning, placing on the market of residential ventilation products and systems to provide the predetermined performance, comfort conditions of temperature, air velocity, humidity, hygiene and sound in the occupied zone. It defines those performance characteristics (mandatory or optional) which are determined, measured and presented according to relevant test methods. It provides a classification scheme, which leads to a full definition of product properties based on test methods described in various European Standards, and gives an overview of the test standards. Distinction between mandatory and optional requirements is left to each European and national regulation(s). The codification part in Annex B and the classification part in Clause 8 apply to the following products: - unidirectional mechanical supply and exhaust residential ventilation units according to EN 13141-4:2021 and EN 13141-6:2014; - ducted mechanical bidirectional residential ventilation units according to EN 13141-7:2021; - non-ducted mechanical bidirectional residential ventilation units according to EN 13141-8:2022. This document does not apply to other products such as filters, fire dampers, ducts, control devices and sound attenuators, which may also be incorporated in residential ventilation. This document specifies in Annex ZA and Annex ZB the requirements of EU 1253/2014 and EU 1254/2014 for residential ventilation units below 1 000 m3/h air volume flow. This document does not cover requirements raised by European Directives (e.g. low voltage directive, EMC directive) and other requirements such as corrosion, reaction to fire and snow penetration.

 

This document specifies the dimensions of, and additional requirements for, fork carriers (as defined in ISO 5053-3) and hook-on type fork arms (as described in ISO 2331), to permit the interchangeability of fork arms (as defined in ISO 5053-2) or other attachments, relative to the truck-rated capacity and fork arm type, on fork-lift trucks up to and including a rated capacity of 10 999 kg.

 

This project aims at covering the line 16 of the standardisation request and will provide: • General description of the Product with digital elements belonging to that category and the product and/or components such Product with digital elements may integrate, including – amongst other: o detailed description of that product category using in: ? Identity management systems hardware and software are products with digital elements that provide mechanisms for identity lifecycle management, such as identity provisioning, maintenance, authentication, authorisation and deprovisioning, and including associated metadata. ? Privileged access management hardware and software are products with digital elements that authenticate and authorise users or devices, granting or denying access to digital resources or to physical locations. ? This category includes but is not limited to products (hardware, software and communication protocol) with digital elements that have the core functionality of either or both identity management and privileged access management; authentication and access control readers; biometric readers; single sign-on software; federated identity management software, protection and safety management (such as access control, intrusion alarm, CCTV and fire safety systems) and multi-factor authentication software. o Intended product purpose and reasonably foreseeable use in the above categories; o Identification of the various types of Products with digital elements; o Delineation and interplay with the following other categories of Product with digital elements (identified by their line in the standardization request): ? line 17 ? line 18 ? line 20 ? line 24 ? line 28 ? line 29 ? line 32 ? line 35 ? line 37 ? line 38 ? line 39 ? line 41 • Description of their life cycle; • Relevance of cybersecurity essential requirements including the cybersecurity assessment requirements; • Definition of applicable risk profiles to be considered for these Product with digital elements; • Applicable cybersecurity requirements ensuring fulfillment of the essential requirements for each risk profile; • Applicable cybersecurity assessment requirements for each risk profile. A base document is provided • Defining the risk profiles; • Identifying initial cybersecurity security requirements.

 

This document defines cyber security requirements for products with digital elements belonging to product category “Hardware Device with Security Boxes” (hereinafter called “Product” or “HWSB product”). The technical description of “Hardware Devices with Security Boxes” can be found in Annex II of [CRA]. The Hardware Devices with Security Boxes in scope are designed for deployment in a range of environments and where the threat landscape includes attackers with various attack potential. HWSB are hardware-based systems intended to provide secure storage, processing and use of sensitive data, including cryptographic assets, within a protected hardware boundary (envelope). This document applies to the HWSB part of the product. The applicability of this document to specific products is determined based on their intended purpose, use case and risk assessment.

 

ISO 25237:2017 contains principles and requirements for privacy protection using pseudonymization services for the protection of personal health information. This document is applicable to organizations who wish to undertake pseudonymization processes for themselves or to organizations who make a claim of trustworthiness for operations engaged in pseudonymization services. ISO 25237:2017 - defines one basic concept for pseudonymization (see Clause 5), - defines one basic methodology for pseudonymization services including organizational, as well as technical aspects (see Clause 6), - specifies a policy framework and minimal requirements for controlled re-identification (see Clause 7), - gives an overview of different use cases for pseudonymization that can be both reversible and irreversible (see Annex A), - gives a guide to risk assessment for re-identification (see Annex B), - provides an example of a system that uses de-identification (see Annex C), - provides informative requirements to an interoperability to pseudonymization services (see Annex D), and - specifies a policy framework and minimal requirements for trustworthy practices for the operations of a pseudonymization service (see Annex E).

 

The primary purpose of ISO/IEC 19788 is to specify metadata elements and their attributes for the description of learning resources. This includes the rules governing the identification of data elements and the specification of their attributes. ISO/IEC 19788 provides data elements for the description of learning resources and resources directly related to learning resources. ISO/IEC 19788-3:2011 is designed to help implementers with a starting point for adopting ISO/IEC 19788, defining an application profile that specifies, through adding constraints to the use of some data elements, how the ISO/IEC 19788-2 element set can be used.

 

This document specifies the requirements and their test methods applicable to all elastomeric auxiliaries used for orthodontics both inside and outside the mouth, in conjunction with fixed and removable appliances.

 

The work item aims to differentiate between biodegradable and non-biodegradable plastic materials. Non-biodegradable plastics are defined as those plastics which do not biodegrade, even in conditions which are conducive to the process. In contrast, the biodegradation of biodegradable plastics occurs when they come into contact with active microorganisms, under conditions that are conducive to biodegradation. This process is analogous to the biodegradation of natural polymers. The plastic materials that are categorised as being intrinsically biodegradable can be utilised in the design of products with a high risk of dispersion. The test scheme is not intended to be applicable to any specific application. Instead, the objective is to develop a framework methodology that can be utilised across diverse industrial sectors for the identification of biodegradable plastics, with the subsequent application of these plastics in the manufacture of various products and for different purposes. The work item does not intend to characterise and evaluate the environmental impact of products containing plastics identified as biodegradable. The test scheme should address the definition of intrinsic biodegradability of plastic materials, without determining the hazard potential of the products, which necessitates a distinct assessment that extends beyond the scope of this particular work item. The rate of biodegradation of a plastic object is not the focus of this particular work item, as it is contingent on environmental conditions. The test scheme to be developed will not be sufficient to carry out an analysis of the ecological risk associated with the dispersal of products, as this requires an assessment of the intrinsic hazard, of the environmental fate, in addition to the assessment of biodegradability.

 

This document is applicable to self-propelled and pedestrian propelled manual and semi-manual industrial trucks as defined in ISO 5053 1:2020 including their load handling devices and attachments (hereafter referred to as trucks) intended for use in potentially explosive atmospheres.NOTE 1 Attachments mounted on the load carrier or on fork arms which are removable by the user are not considered to be a part of the truck.This document specifies supplementary technical requirements for the prevention of the ignition of an explosive atmosphere of flammable gases, vapours, mists or dusts by industrial trucks of equipment group II and equipment category 2G, 3G, 2D or 3D.NOTE 2 The relationship between an equipment category (hereafter referred to as category) and the corresponding zone (area classification) is shown in informative Annex B.This document does not apply to:— trucks of equipment group I;— trucks of equipment group II, equipment category 1;— trucks intended for use in potentially explosive atmospheres with hybrid mixtures;— protective systems.This document does not apply to trucks intended for use in potentially explosive atmospheres of carbon disulfide (CS2), carbon monoxide (CO) and/or ethylene oxide (C2H4O) due to the special properties of these gases.Technical requirements relating to lithium-ion batteries and fuel cells as energy sources are not given in this document due to their specific hazards.

Tämä dokumentti on DRM-suojattu. DRM-suojattujen tiedostojen lukemiseen on välttämätöntä asentaa koneelle ilmainen FileOpen-liitännäinen (FileOpen plug-in). Jos sinulla ei ole oikeutta asentaa ohjelmia omalle päätelaitteellesi, ota yhteyttä oman organisaatiosi IT-tukeen. FileOpen liitännäisen saat ladattua osoitteessa http://plugin.fileopen.com/all.aspx. Onnistuneen asennuksen jälkeen avaa standardiehdotus Acrobat Readerilla, jotta lisäosa toimii oikein.